To ensure you meet the Engineering Accreditation Commission of ABET requirements, http://www.abet.org, all three electives must be upper-division or graduate engineering courses.
In choosing your technical electives, you should keep in mind that these classes are meant to broaden your educational background. You can select courses in different areas, to enhance your breadth of knowledge. However, if you have a specific career objective in mind, you may choose an area of specialization and select three electives within the same discipline. Keep in mind that several classes outside of the NanoEngineering Department (biotechnology, microelectronics, and materials), need additional prerequisites and may extend your program completion time.
If you are planning for graduate school, you may want to consider the general, but more fundamental, area of Engineering Sciences. In all cases, we also accept graduate level courses that pertain to each area. A petition must be submitted for undergraduate and graduate courses not on the pre-approved list below. Undergraduate students who would like to enroll in graduate level courses must have an overall GPA of 3.0 or above.
The courses listed here other than NANO and CENG are under the control of other departments. All departments strictly enforce the course prerequisites for all students. Each student is responsible for determining the prerequisites, when the courses are to be offered, and making a schedule of taking the courses that fits into his or her own graduation plan.
NANO 103, 242, 244, 262
CENG 207/ NANO 243, 254, 256
BENG 100, 110, 112A, 112B, 130, 186A
Microelectronic Devices and Materials
Fabrication of electronic materials or microelectronics devices involves many chemical engineering principles and processes. Selections from the following courses would give a sound background for understanding basic physics and device technology. With this option, virtually all ECE classes require petition with the ECE Department. WebReg would not work. These classes require at least PHYS 2D as a prerequisite. As a substitute for PHYS 2D, CHEM 130 may be taken as part of advanced chemistry requirement.
CENG 134, 157
ECE 103, 134, 135A, 136L
This is an area with emphasis on mechanical engineering, which like chemical engineering, is also a broad-based engineering discipline.
MAE 104, 130A, 130B, 131A, 149, 160
This is a general area with emphasis on fundamental engineering sciences. This area is intended for those who are serious about graduate research. In addition to the following suggestions, students are free to choose other classes, especially graduate level courses.
MAE 104, 105, 107, 140, 149
Environmental engineering is one of the industrial sector that makes extensive use of chemical engineering. In addition to the development of technologies for hazardous waste treatment, there is also need for the design of new processes with low waste emission. Government agencies also need chemical engineers for various monitoring and regulatory activities. (The following MAE courses are only offered on a sporadic basis.)
MAE 119, 122, 124/ ESYS 103*, 125B, 126A, 126B, 127
*TE credit cannot be given for both MAE 124 and ESYS 103
Materials Science and Engineering
Materials science and engineering rest heavily on physical chemistry. While there are more traditional applications in polymer processes, new areas of development are in composite and advanced materials. With a firm background in physical chemistry, chemical engineering major should have no problem with the listed graduate level materials science courses. You are recommended to take Chem 130 as part of your advanced chemistry requirement courses.
CENG 134/ NANO 134/ CHEM 134
NANO 100L, 174, 174L
MATS 201A, 201B, 201C, 205A, 227
*Credit cannot be given for more than one course between CENG 134, NANO 134, and CHEM 134
These courses address the fundamental chemical and physical issues that arise when engineers work at the nanoscale.
NANO 101**, 102, 103, 104, 106, 108, 110, 111, 112, 140, 145, 146, 148, 150, 156***, 158, 161, 162, 164, 168, 201**, 243*,253
CENG 134,157, 207*, 208, 211**, 212, 213, 214, 215
*Credit cannot be given for both CENG 207 and NANO 243
**Credit cannot be given for both CENG 211/ NANO 201, and NANO 101
***NANO 156 and MAE 166 are cross-listed courses. CENG majors must enroll in NANO 156
Process Dynamics and Control
The chemical process industries were among the first to be automated. Process control has become an integral part of process design and operation. The modeling of the dynamics of chemical and biochemical processes is crucial to their understanding and control.
MAE 140, 142, 143A, 143C, 149, 180A
To fulfill the basic process control requirement for the B.S. degree, students can take one of the following three courses: CENG 120*, MAE 143B, or ECE 171A. (*CENG 120 can be replaced by MAE 143B or ECE 171A only if a student chooses Process Dynamics and Control as the Area of Specialization). The basic process control requirement course above that you take does not fulfill one of the 3 AS course requirements.
Thermal Engineering and Systems
This is an area that offers opportunities for energy conversion and thermo-sciences in the aerospace, utility and other energy-related industries.
MAE 110B , 113, 118, 119, 120
CENG 199. Independent Study for Undergraduates (4-4) Chemical Engineering students may take CENG 199 under the guidance of a Chemical Engineering faculty member. This course is taken as a Technical Elective on a P/ NP basis. Eligible students must have completed at least 90 units and must have a UCSD cumulative GPA of 3.0 or better. The two CENG 199s must be done in consecutive quarters and the student must find a faculty member who will oversee the research project. After obtaining the faculty member’s concurrence on the topic and scope of the study, the student must submit a Special Studies Course form (each quarter) and CENG 199 Contract form (the first quarter) to the Undergraduate Affairs Committee. These forms must be completed, approved, and processed prior to the Add Deadline. After the second quarter is completed, the student must submit an Undergraduate Student Petition to have the work accepted as two Technical Elective courses. A final report must be attached to the petition for the faculty member and Undergraduate Affairs Committee to review. Detailed policy in this regard and the requisite forms may be obtained from the Student Affairs Office.
Global TIES and Engineering Leadership (Effective Spring 2015)
Students can choose one of the options as one approved Focus Elective:
- ENG 100D (4 units): Design for Development
- ENG 100L (2 units) and ENG 100L (2 units): Design for Development Lab (total of 4 units) - can take in two quarters
- ENG 100B (2 units) and 100L (2 units): Engineering Leadership and Design for Development Lab (total of 4 units) - can take in two quarters